| Categories | Agricultural Equipment and Harvesting Machinery Manuals, New Holland Agricultural Equipment Manuals |
|---|---|
| Tags | New Holland TC25, New Holland TC29, New Holland TC33 |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
New Holland TC25, 29, 33 Boxer Parts List & Mounting Instructions Jodale · Perry Printed: 2004/01 New Holland TC25, 29, 33 Boxer Mounting Instructions Standard Parts List Qty L&R Description Front Bracket Weldment Photo L&R Rear Bracket Weldment 4 No-Loader Bracket Spacer 2 1 Mid-Mount Spacer (Tube spacers) Clutch Shield 1 Brake Shield (2 parts) L&R 2 2 15 LF 7 LF L&R Front Enclosure Shields Cab Lift Brackets (1 ” Tube) 3/8 ” Black Snap Caps 180° O-rubber 90° O-rubber Floormat, Platform L&R L&R Floormat, Clutch/Brake Floormat, Platform Extension NOTE: All references to left and right are taken from the operator’s point of view when he/she is sitting in the driver’s seat.
Agricultural Equipment Manual Free Download. Lawn Mowers Specs. Power Harvesting Machinery Free Specification Download PDF.
01 New Holland TC25, 29, 33 Boxer Mounting Instructions 2 sets Loader Stabilizer Brackets 2 Fender Reinforcement Brackets 1 SMV Sign Mount Bracket L&R Flasher Light Brackets 4 8 1 20 ” 14GA Black Wire Connector, Butt, Blue, 14GA Circuit Breaker Mount Plate NOTE: All references to left and right are taken from the operator’s point of view when he/she is sitting in the driver’s seat. 02 New Holland TC25, 29, 33 Boxer Mounting Instructions Standard Bolts List Qty Description Bolt, Hex, ½ ” x 3 “, Gr. 8, Yellow Dichrome Nut, Hex, ½ “, Gr. 8, Yellow Dichrome Washer, Lock, ½ ” Washer, Flat, Steel, 9/16 ” x 2 ½ “, Plated Washer, Flat, Rubber, 9/16 ” x 2 ½ “, Black Isolator, Rubber, ½ ” x 2 ½ “, Black Bolt, Flange, ¼ ” x ½ “, Yellow Dichrome Nut, Flange, ¼ “, Macro-Black Bolt, Hex, M16 x 2.0 x 60MM, Gr. 8.8, Yellow Dichrome Washer, Lock, 5/8 ” Bolt, Hex, 3/8 ” x 1 ½ “, Gr. 8, Yellow Dichrome Nut, Flange, 3/8 “, Gr. 8, Yellow Dichrome Screw, Button-Head, 5/16 ” x 1 ” Washer, Fender, 5/16 ” Nut, Nylon-Locking, 5/16 “, Yellow Dichrome Bolt, Flange, 3/8 ” x ¾ “, Yellow Dichrome Washer, Flat, 3/8 ” Nut, Flange, M6 x 1.0, Yellow Dichrome NOTE: All references to left and right are taken from the operator’s point of view when he/she is sitting in the driver’s seat. 03 New Holland TC25, 29, 33 Boxer Mounting Instructions Optional Parts Lists Heater Option (if equipped) Qty 25 LF 1 1 2 Description Hose, Heater, 3/8 “ID Fitting, 3/8NPT x 3/8 ” Barb, 180° Fitting, 3/8NPT x 3/8 ” Barb, 90° Clamp, Hose, HS-6 Photo NOTE: All references to left and right are taken from the operator’s point of view when he/she is sitting in the driver’s seat. 04 New Holland TC25, 29, 33 Boxer Mounting Instructions NOTE: Use the following torque specifications for all hardware: ½ ” hardware 73 ft-lbs, 3/8 ” hardware 42 ft-lbs, 5/8 ” hardware 177 ft-lbs. 1. Prior to cab installation, remove 2-post ROPS guard (keep hardware to be re-used later); upper toolbox crossmember (re-installed later); disconnect rear flashers; and disconnect lower 3-point support (remounted on rear cab bracket). If tractor is equipped with front loader, detach loader to make cab installation easier. 2. Take the left rear cab bracket and position it on the axle of the tractor as shown in Figure 1. Re-use the factory ROPS hardware and loosely bolt onto the axle. Re-install the lower ROPS crossmember with the factory hardware. 3. Repeat for the right side and right Re-bolt the fender to the rear bracket as bracket. See Figure 2. Loosely fasten well. DO NOT securely fasten the the lower ROPS crossmember into place. bracket until the cab has been installed. Figure 3 Figure 1 Figure 2 4. Take the left front cab bracket. If tractor is not equipped with a mid mount mower or loader it will be necessary to use two plate spacers per side for the loader, and use one tube spacer for NOTE: All references to left and right are taken from the operator’s point of view when he/she is sitting in the driver’s seat. 05 New Holland TC25, 29, 33 Boxer Mounting Instructions mid-mount attachment for the lower, Figure 5 rear bolt hole on the bracket. If tractor has front loader remove the three bolts for the bracket as shown in Figure 3 for the front bracket, and then use new hardware. If tractor has no loader, use the provided M16 x 2.0 x 60MM hex bolts and 5/8 ” lock washers to fasten front bracket into place.